Key takeaways
- Compare the best featherboards for band saw resawing, from a silicone resaw guide to magnetic and tandem boards, with specs, fit checks and setup tips.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Resawing is the band saw cut most likely to wander. A tall board presents a long edge to the blade, the fence contact patch is narrow compared with the board’s height, and any slight drift at the infeed end shows up as a tapered slice or ruined bookmatched veneer. A featherboard set just ahead of the blade holds the stock against the fence with steady, spring-like pressure for the full length of the cut, so your hands can focus on feeding at an even rate.
The catch is that resawing makes demands a general-purpose featherboard does not always meet. It has to reach up a tall workpiece, fit the smaller slots on many band saw tables, and press along the leading edge of the stock without crowding the blade. The five picks below were chosen for exactly that work: a tall silicone resaw guide, a magnetic board, a one-knob spiral design, a stacking tandem pair, and a budget set.
As an Amazon Associate, we earn from qualifying purchases.
Quick Answer
For most resawing, the BOW Products GuidePRO GP5 is the standout pick: its 6-inch silicone feather presses along the leading edge of tall stock, and its cam base fits 15 mm, 5/8-inch and 3/4-inch slots. On cast-iron tables, the Magswitch Universal Featherboard Pro locks down anywhere with switchable magnets. The Hedgehog sets up fastest, the Milescraft 1407 stacks for tall stock, and the Zeromall set is the budget pick.
Table of Contents
- Quick Answer
- BOW Products GuidePRO GP5
- Magswitch Universal Featherboard Pro
- The Hedgehog Spiral Featherboard
- Milescraft 1407 D/T FeatherBoard
- Zeromall Stackable Featherboard Set
- How to Choose a Featherboard for Resawing
- Who Should Skip a Resaw Featherboard
- FAQ
- Final Verdict
- Product and ASIN Reference
BOW Products GuidePRO GP5
The GuidePRO is the only pick here designed from the start for the band saw rather than adapted to it. Instead of a row of fingers, it uses a single tall feather made of flexible silicone that bears against the leading edge of the workpiece before the blade. That continuous contact is what resawing needs: pressure stays even along the face of a tall board, the silicone damps vibration, and because the feather is non-marring and replaceable, it can grip flat, thin or irregular stock without denting it.
Mounting is handled by interchangeable miter cams in 15 mm, 5/8-inch and 3/4-inch sizes, covering most band saw tables, and the sliding base works where the miter slot sits anywhere from 2 to 8 inches from the blade. A handle and locking lever set the pressure, and an optional extension kit adds a taller feather for stock above the standard working height. This is the premium pick in the group, and the one to choose if resawing is a regular part of your work.
Specs:
- Feather: 6-inch vertical silicone feather, replaceable
- Mounting: miter cams in 15 mm, 5/8-inch and 3/4-inch sizes
- Fit range: miter slots 2 to 8 inches from the blade
- Extension: optional extension kit adds 4 inches of feather height
- Warranty: 1-year limited warranty
- Tier: premium
Magswitch Universal Featherboard Pro
Band saw tables are small, and their miter slots are not always where you want them. The Magswitch Universal Featherboard Pro removes the slot from the equation: two switchable magnets in a wide base lock the board to any cast-iron or steel table surface, wherever the cut requires, and release with a twist when you want to move it. Compressible gaskets under the base keep its grip even when part of the base bridges the miter slot, and the board works for left-hand or right-hand feeds.
Published specifications list a nominal maximum breakaway force of 126 pounds and a maximum shear resistance above 50 pounds, far more holding power than a resaw cut can challenge. Micro-adjustable bump stops let it double as a repeatable stop, and the design is stackable for taller stock. The one hard requirement is a ferrous table: it will not grip aluminum or phenolic surfaces. On a cast-iron band saw table, it is the most flexible mounting system in this roundup.
Specs:
- Model: 81101303
- Mounting: two switchable magnets, no miter slot required
- Holding force: 126 lb nominal maximum breakaway, 50+ lb shear (manufacturer specification)
- Footprint: 5.29 x 6.23 inches
- Weight: 1.2 lb
- Extras: micro-adjustable bump stops, stackable design
- Tier: premium
The Hedgehog Spiral Featherboard
The Hedgehog replaces the usual row of fingers with a spiral-shaped body that pivots on a single point. Setup is a one-handed routine: drop the clamp into the miter slot, swing the spiral face against the stock until the pressure feels right, and tighten the one knob. That speed matters when test-fitting pressure on offcuts before committing a good board, and the reversible body works on either side of the blade.
The clamp is cast, CNC-milled aluminum sized for a standard 3/4-inch miter slot, and the body is molded from high-impact DuPont nylon. Note the fit limit before ordering: the clamp does not fit 5/8-inch slots, ruling it out for some smaller band saws. On a saw with a 3/4-inch slot, it is a mid-range pick that trades the tandem reach of stacked boards for the quickest setup in the group.
Specs:
- Model: HH-100
- Design: spiral feather with single pivot and one locking knob
- Miter clamp: cast CNC-milled aluminum, 3/4-inch slot only
- Body material: high-impact DuPont nylon
- Dimensions: 6.5 x 0.63 x 9.25 inches
- Weight: 8.8 oz
- Tier: mid-range
Milescraft 1407 D/T FeatherBoard
Tall resaw stock is where a single row of fingers runs out of reach, and the Milescraft 1407 answers that problem by putting two featherboards in the box. Run one board for ordinary work, or join the pair with the included spacer to build a tandem unit that presses at two heights on a tall board. The split-rail miter bar expands inside the slot as you tighten the knobs, and a pre-load tension design keeps pressure even across the face of the fingers.
Compatibility is the other strength. The kit includes metal miter bars in both 5/8-inch and 3/4-inch widths, two of each, plus 1/4-inch T-slot bolts, so the same set fits the narrower slots on many band saws as well as standard table saw slots. Dual slide motion helps during setup, and for resawing wide boards on a saw with a 5/8-inch slot this mid-range kit may be the most practical pick here.
Specs:
- Contents: two featherboards with stacking spacer
- Miter bars: 5/8-inch and 3/4-inch metal bars, two of each
- Hardware: 1/4-inch T-slot bolts included
- Design: split-rail bar with pre-load tension, dual slide motion
- Warranty: 3-year warranty
- Tier: mid-range
Zeromall Stackable Featherboard Set
The Zeromall set covers the resawing basics at a budget tier. Two featherboards with angled fingers can be used singly or stacked with the included spacers, putting pressure at two heights on a taller board like pricier tandem kits. A double lock system with wedge lock hardware holds the setting once you dial it in.
Mounting hardware covers both 3/4-inch and 3/8-inch T-tracks, with brackets for horizontal mounting and rails for vertical mounting, which gives the set a route onto band saw tables, table saws and router tables. The fit hardware is less refined than the cam and magnet systems above it, so expect a little more time on initial setup. For occasional resawing and thin-strip work, it delivers the essential function — steady fence pressure ahead of the blade — at the lowest tier in this group.
Specs:
- Contents: two stackable featherboards with plastic spacers
- Locking: double lock system with wedge lock hardware
- Track fit: 3/4-inch and 3/8-inch T-tracks
- Mounting: horizontal brackets and vertical rails included
- Tier: budget
How to Choose a Featherboard for Resawing
Start with the slot, because it eliminates options faster than any other factor. Measure the miter slot on your band saw table: many band saws use a 5/8-inch slot rather than the 3/4-inch slot common on table saws, and some have no usable slot near the blade at all. A 3/4-inch-only clamp such as the Hedgehog will not fit a 5/8-inch slot, while cam-based and multi-bar kits cover both sizes. If your table is cast iron, a magnetic board sidesteps the question entirely.
Next, match the feather height to your stock. Resawing asks a featherboard to press on boards that may be 6 inches wide or more, so look for a tall feather, a stacking or tandem design, or an extension option. A single low row of fingers controls only the bottom of a tall board and lets the top lean away from the fence.
Finally, think about pressure style. Silicone and foam feathers give continuous, forgiving contact that suits thin veneer slices and irregular stock. Rigid fingers give firmer, more localized pressure for thick, straight boards. Magnetic boards add positioning freedom that helps on small band saw tables where the slot sits too far from the blade.
Who Should Skip a Resaw Featherboard
Skip the featherboard if your resawing is done with a power feeder, which already provides continuous pressure and makes a featherboard redundant. Also skip it if you mostly resaw very short stock: a featherboard needs enough board length ahead of the blade to register against, and stubby pieces are better handled with a tall fence and push blocks. Owners of band saws with aluminum tables should skip the magnetic option specifically, since the magnets have nothing to grip. And if your saw’s miter slot is an unusual size that none of the included cams or bars match, a fence-clamped shop-made board beats forcing a fit.
FAQ
Where should a featherboard sit when resawing on a band saw?
Position it on the infeed side so the feather presses the stock against the fence just before the blade. Never place a featherboard alongside or past the blade, where it can pinch the cut closed and trap the workpiece.
Can one featherboard handle tall resaw stock?
Only if it is tall enough or stackable. A 6-inch feather, a tandem pair joined with a spacer, or two stacked boards can cover tall stock. A single low featherboard controls only the bottom edge and lets the top of the board drift.
Will a table saw featherboard fit my band saw?
Sometimes. Check the miter slot width: many band saws use 5/8-inch slots while most table saw featherboards assume 3/4 inch. Kits with multiple cams or both bar sizes fit both machines, and magnetic boards fit any cast-iron table regardless of slot.
Does a featherboard stop band saw blade drift?
No. Drift is a blade, tension and fence alignment issue, and it is corrected by aligning the fence to the blade’s natural cutting angle. A featherboard holds the stock firmly against that corrected fence, which makes the cut more consistent, but it does not fix drift itself.
Final Verdict
For dedicated resawing, the BOW Products GuidePRO GP5 is the most purpose-built choice, with a tall silicone feather and cams that match band saw tables. The Magswitch Universal Featherboard Pro is the pick for cast-iron tables and awkward slot positions, the Hedgehog wins on setup speed, the Milescraft 1407 covers tall stock and both common slot sizes in one mid-range kit, and the Zeromall set handles the job at a budget tier. Match the mounting system to your table first, and any of the five will make resaw cuts straighter and easier to control.
Related guides
You might also like
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.