Key takeaways
- Compare the best router lift systems for router tables, with plate sizes, motor fit, adjustment range and above-table bit changes for each pick.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
The best router lift system for most router tables is the JessEm Mast-R-Lift II, because its hard-anodized aluminum plate, cam lock and broad motor fit cover the widest range of shops. The Kreg Precision Router Lift is the strongest alternative for owners who want one crank turn to equal a predictable step, and the JessEm Rout-R-Lift II covers smaller 3-1/2 inch motors at a budget tier.
A lift replaces the fixed base you would otherwise reach under the table to adjust. The router motor clamps into a carriage under the plate, and a crank or wheel on top raises and lowers it, so bit height changes and bit swaps happen above the table instead of by feel. The five systems below are the established names in this category, compared on plate size, motor diameter fit, adjustment mechanism and ring system, using only published manufacturer specifications.
As an Amazon Associate, we earn from qualifying purchases.
Quick Answer
For a standard 9-1/4 by 11-3/4 inch table opening, start with the JessEm Mast-R-Lift II if your motor is a large 4.2 inch model, or the Kreg Precision Router Lift if you want an indexing crank that returns to earlier settings. Owners of 3-1/2 inch motors on a tighter budget should look at the JessEm Rout-R-Lift II or the newer Rout-R-Lift 3.5XT.
Table of Contents
- JessEm Mast-R-Lift II
- Kreg Precision Router Lift
- Incra Mast-R-Lift II
- JessEm Rout-R-Lift II
- JessEm Rout-R-Lift 3.5XT
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
JessEm Mast-R-Lift II
The Mast-R-Lift II is the reference point in this category and the premium pick here. Its top plate is machined from 3/8 inch solid aluminum and hard anodized, and the carriage uses an adjustable clamping block system instead of fixed pads, so one lift accepts a long list of motors straight out of the box. JessEm publishes fit for 18 different router motors from 8 manufacturers, including the Porter-Cable 7518, 690 and 890 series, Bosch 1617 and 1618, DeWalt 610 and 618, Makita 1101, Hitachi M12VC and KM12VC, several Milwaukee models and the Ridgid R29302.
Height changes run on a lift screw carried by double-sealed ball bearings, which keeps cranking effort low and consistent. An exclusive cam locking system lets you lock the carriage after setting a height, a useful safeguard before a heavy cut. Bit changes are done above the table, and the plate ships with three insert rings. If you run a big motor and make frequent, fine height adjustments, this is the lift the others are measured against.
Specs
- Model: JessEm 02120
- Plate: 9-1/4 x 11-3/4 inches, 3/8 inch hard-anodized aluminum
- Motor fit: up to 4.2 inch diameter; 18 motors from 8 manufacturers listed
- Mechanism: lift screw on double-sealed ball bearings
- Locking: cam lock system
- Insert rings: 3 included
- Bit changes: above the table
- Tier: premium
Kreg Precision Router Lift
The Kreg Precision Router Lift (PRS5000) is built around repeatability. Its carriage is bearing-guided, and each full rotation of the adjusting crank moves the carriage exactly 1/16 inch, so returning to a previous bit height is a matter of counting turns rather than re-measuring. A built-in micro-adjust scale supports finer dialing once you are close.
Kreg publishes compatibility with more than 20 popular router models without pads or adapters, covering Porter-Cable 7518 and 690/890, Milwaukee 5625, Bosch 1617/1618, Craftsman and DeWalt 618 motors, among others. The plate is 3/8 inch hard-anodized aluminum in the standard 9-1/4 by 11-3/4 inch footprint, so it drops into all Kreg router tables and many competing tops. Above-table collet access allows bit changes from the top, and the lift carries a three-year warranty. It is the natural pick for a Kreg table owner, and a strong mid-range to premium option in any standard opening.
Specs
- Model: Kreg PRS5000
- Plate: 9-1/4 x 11-3/4 inches, 3/8 inch hard-anodized aluminum
- Motor fit: 20 or more router models, no pads or adapters required
- Mechanism: bearing-guided carriage; one crank turn equals 1/16 inch
- Travel: about 3 inches of carriage travel
- Bit changes: above the table
- Warranty: 3 years
- Tier: mid-range to premium
Incra Mast-R-Lift II
Incra builds its version of the Mast-R-Lift II around one distinctive feature: the MagnaLOCK reducing ring system. Instead of threaded or twist-lock rings, steel reducing rings snap into the plate magnetically, so ring changes are instant and tool-free. Five steel rings are included, covering openings from a small bit hole up to a wide clearance for large panel-raising bits.
The lift itself uses a direct-drive screw on ball bearings, with a 16 threads-per-inch lift screw for fine control, and a printed gauge that shows how far the carriage has moved. The plate is the standard 9-1/4 by 11-3/4 inch size at 3/8 inch thick, sized for Incra router tables. Included components are the lift, a crank handle and the ring set, and the unit weighs about 11 pounds. Choose this one if fast ring swaps are part of your workflow, for example when you move between small profile bits and large door bits in the same session.
Specs
- Model: Incra Mast-R-Lift II
- Plate: 9-1/4 x 11-3/4 inches, 3/8 inch aluminum
- Ring system: MagnaLOCK magnetic steel rings, 5 included
- Mechanism: direct-drive screw on ball bearings, 16 TPI lift screw
- Included: lift, crank handle, ring set
- Weight: about 11 pounds
- Warranty: 1 year
- Tier: premium
JessEm Rout-R-Lift II
The Rout-R-Lift II is JessEm’s budget-tier answer for the most common motor size in home shops: 3-1/2 inch diameter fixed-base motors. JessEm lists fit for the Porter-Cable 690 and 890 series, DeWalt 610, 616 and 618, and Bosch 1617 and 1618, which covers the routers many woodworkers already own.
To reach its tier, it trades the Mast-R-Lift’s machined aluminum plate for a phenolic plate in the same 9-1/4 by 11-3/4 inch footprint, and it keeps the essentials: above-the-table bit changes and cranked height adjustment from the top. It will not accept the large 4.2 inch motors such as the Porter-Cable 7518, so it suits a dedicated mid-size router rather than a future-proof setup. For a first lift under a 2-1/4 horsepower class motor, it delivers the core convenience of a lift without paying for capacity you cannot use.
Specs
- Model: JessEm 02310
- Plate: 9-1/4 x 11-3/4 inches, phenolic
- Motor fit: 3-1/2 inch diameter motors, including Porter-Cable 690/890, DeWalt 610/616/618, Bosch 1617/1618
- Bit changes: above the table
- Height adjustment: cranked, from above the table
- Tier: budget
JessEm Rout-R-Lift 3.5XT
The Rout-R-Lift 3.5XT is the current mid-range step between the Rout-R-Lift II and the Mast-R-Lift II. It pairs a heavy-duty aluminum lift mechanism with a phenolic top plate, keeping the standard 9-1/4 by 11-3/4 inch footprint and 3/8 inch plate thickness that fits JessEm and Kreg tables and shop-built tops cut to that opening.
Like the Rout-R-Lift II, the clamp closes directly on 3-1/2 inch motor bodies with no adapter, covering the Porter-Cable 690 and 890, DeWalt 610, 616 and 618, Bosch 1617 and 1618, and the Skil and Craftsman fixed-base motors built to the same size. Insert rings use a twist-lock design, and bit changes are handled above the table. It is the sensible pick if you want a sturdier carriage than the entry model but have no plans to run a 4.2 inch motor.
Specs
- Model: JessEm 02318
- Plate: 9-1/4 x 11-3/4 inches, phenolic top plate, 3/8 inch thick
- Motor fit: 3-1/2 inch diameter motors, no adapter needed
- Mechanism: heavy-duty aluminum lift with double-sealed bearings
- Insert rings: twist-lock style
- Bit changes: above the table
- Tier: mid-range
How to Choose
Start with two measurements. First, the plate opening in your table top: most lifts here use the 9-1/4 by 11-3/4 inch standard, but some tables, notably older Rockler tops, use an 8-1/4 by 11-3/4 inch opening that needs a different plate variant. Second, your motor’s body diameter. Lifts are built around either the 3-1/2 inch class (Bosch 1617, Porter-Cable 690/890, DeWalt 618) or the 4.2 inch class (Porter-Cable 7518, Milwaukee 5625). A 3-1/2 inch lift cannot grow into a big motor later.
Next, weigh the adjustment system. An indexing crank, like the Kreg’s 1/16 inch per turn, makes repeat setups easy to return to. A lock, such as the JessEm cam lock or a positive carriage lock, matters most for heavy cuts where vibration could let a setting drift. Then consider the ring system: magnetic rings swap fastest, twist-lock rings are the common middle ground, and the included ring sizes should cover both your smallest bits and any large panel raisers you run. Finally, confirm the lift supports above-the-table bit changes with your motor; that single feature is most of the day-to-day convenience a lift adds.
Who Should Skip
Skip a lift if your router already has a fixed base with a good above-table adjustment system and you rarely change bits; a simple insert plate may cover your needs. Skip the 3-1/2 inch models if there is any chance you will move to a 3-1/4 horsepower motor, since the carriage cannot accept it. Skip lifts entirely if you only use a plunge router, because these systems clamp bare fixed-base motor bodies, and plunge bases do not fit the carriages listed here. And if your table opening is a non-standard size, solve that first; no lift on this list will sit flush in the wrong opening.
FAQ
Will a router lift fit my existing router table?
Usually, if your top uses the common 9-1/4 by 11-3/4 inch plate opening. Measure the opening before ordering, because some tables use an 8-1/4 by 11-3/4 inch opening instead, and each lift is sold in plate variants matched to one size or the other.
Can I use my plunge router in a lift?
No. Router lifts clamp the bare motor body of a fixed-base router. A plunge router’s base and handles do not fit the carriage, so a lift means dedicating a fixed-base motor to the table.
What motor diameter should I measure?
Measure the cylindrical body of the motor itself, not the base. The two common classes are 3-1/2 inch and 4.2 inch. Match that number to the lift’s published fit list, and check your exact model against the manufacturer’s compatibility chart before buying.
Do I still need insert rings with a lift?
Yes. The ring fills the gap between the bit and the plate opening, supporting the workpiece close to the cutter. Different bit diameters need different ring openings, which is why lifts include a ring set and why fast ring systems are worth having.
Final Verdict
For most shops, the JessEm Mast-R-Lift II is the best router lift system: it fits the widest range of motors, locks its setting, and uses the standard plate size. The Kreg Precision Router Lift is the better buy when repeatable, counted-crank setups matter most, and the Incra Mast-R-Lift II earns its place for magnetic ring changes. If your motor is a 3-1/2 inch model, the Rout-R-Lift II covers the basics at a budget tier, while the Rout-R-Lift 3.5XT adds a heavier carriage for a mid-range step up.
Related guides
You might also like
- Best Featherboards for Table Saw and Router Table Cuts
- Best Benchtop Drill Presses With Laser Guides (2026)
- Best Pocket Hole Jigs for Beginners: 5 Top Picks in 2026
- VEVOR Hairpin Table Legs 20 Inch Review: DIY Desk Build
- Best 2-1/2 Inch Dust Collection Hose and Fittings Kits
- Best Smoothing Planes for Furniture Making: 5 Picks
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.