Updated Nov 21, 2026· 9 min read

Key takeaways

  • Compare the best carbide parting tools for woodturning, from brazed-tip USA-made tools to replaceable-blade bars, with cutter widths and handles explained.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

A carbide parting tool swaps the ground high-speed steel edge of a traditional parting tool for a tungsten carbide tip, and that one change rewrites the maintenance routine. There is no bevel to grind and no burr to raise: the tip parts spindle work, cuts sizing grooves, and separates a finished piece from its waste stock, then either gets touched up on a diamond stone, swapped for a fresh blade, or re-sharpened in place. Carbide also holds up in dense hardwoods, segmented blanks, and resin hybrids where steel dulls quickly.

Our top pick: Simple Woodturning Tools Carbide Parting Grooving Tool with 17 Inch Handle. Runner-up: Dirtech Parting Woodturning Tool, 16 Inch.

The five picks below are all dedicated parting and grooving tools, not general turning sets. They split into two families: brazed-tip tools whose carbide is fixed and re-sharpenable, and replaceable-blade bars whose cutter unbolts when it dulls.

As an Amazon Associate, we earn from qualifying purchases.

Quick Answer

For most turners, the Simple Woodturning Tools carbide parting tool with the 17 inch handle is the safest buy: its brazed tip never works loose, it re-sharpens instead of being thrown away, and the long handle steadies deep cuts. On a tighter budget, the Dirtech 16 inch tool uses a replaceable blade, while the Easy Wood Tools tool cuts the narrowest kerf.

Table of Contents

  • Simple Woodturning Tools Carbide Parting Grooving Tool
  • Dirtech Parting Woodturning Tool, 16 Inch
  • Asieg Tool Carbide Parting and Grooving Tool, 19.68 Inch
  • Asieg Tool 8.68 Inch Carbide Parting Tool with Copper Hoop
  • Easy Wood Tools Mid-Size Easy Parting Tool
  • How to Choose a Carbide Parting Tool
  • Who Should Skip These Picks
  • FAQ
  • Final Verdict

Simple Woodturning Tools Carbide Parting Grooving Tool

This is the premium pick, made in Ramsey, Minnesota by Harrison Specialties, a family owned CNC shop. The design is deliberately simple: a nickel plated steel bar with a carbide tip brazed directly onto the end. Because the tip is brazed rather than screwed on, there is no insert screw to loosen mid-cut and no small cutter to drop in the shavings. When the edge dulls, the maker states it can be re-sharpened, and the blade section is replaceable if damaged.

The version listed here pairs the 12 inch tool with the maker’s 17 inch interchangeable handle, an aluminum handle with a foam grip. That long handle is the point of the package: parting is a plunge cut that can grab, and extra leverage keeps the cut tracking straight on larger spindle work. The same handle accepts the maker’s other tools. Mini lathe owners should note the combined length is substantial for very small work.

Specs

    • Maker: Harrison Specialties, made in the USA
    • Model: SPT
    • Tip: brazed tungsten carbide, re-sharpenable
    • Bar: nickel plated steel, 12 inch tool length
    • Handle: 17 inch interchangeable aluminum handle with foam grip

    Dirtech Parting Woodturning Tool, 16 Inch

    The Dirtech is the mid-range workhorse of this group and the most conventional layout: a 6 inch tool bar in a 10 inch solid wood handle, for 16 inches overall. The bar is CNC machined from solid stainless steel with a square 12 by 12 millimeter section, so it sits flat on the tool rest and resists rolling or twisting during a plunge cut.

    Instead of a fixed tip, the Dirtech carries a replaceable parting blade: a 100 millimeter cutter with a carbide tip that bolts to the bar end. The package includes the bar with no blade fitted, one blade, two screws, and a wrench, so setup is part of the first use. When the edge dulls, the blade can be sharpened or replaced rather than the whole tool. That consumable model suits turners who part abrasive or glued-up stock and would rather swap a blade than stop to sharpen.

    Specs

      • Maker: Dirtech
      • Model: ZMB-QD
      • Overall length: 16 inches (6 inch bar, 10 inch handle)
      • Bar: CNC machined stainless steel, square 12 by 12 millimeter section
      • Cutter: replaceable 100 millimeter parting blade with carbide tip
      • Included: 1 carbide blade, 2 screws, 1 wrench

      Asieg Tool Carbide Parting and Grooving Tool, 19.68 Inch

      At 19.68 inches overall, this Asieg Tool model is the longest tool in the roundup, and length is its argument. A longer tool puts more handle behind the rest, which helps when parting larger diameter spindle blanks. The cutting end is a brazed tungsten carbide tip, so the tip cannot come loose in use, and it can be sharpened rather than replaced as a consumable.

      The maker lists the carbide cutter width at 4.2 millimeters, a middleweight kerf: wider than a thin parting tool, so it wastes a little more wood, but stiffer in deep cuts and less prone to wandering. The bar is high carbon steel with a solid wood handle. A replacement blade is sold separately by the maker. Turners with small lathes should measure first, since a tool this long needs swing room behind the rest.

      Specs

        • Maker: Asieg Tool
        • Overall length: 19.68 inches
        • Tip: brazed tungsten carbide, sharpenable
        • Cutter width: 4.2 millimeters
        • Bar: high carbon steel, wood handle
        • Replacement blade: sold separately

        Asieg Tool 8.68 Inch Carbide Parting Tool with Copper Hoop

        The second Asieg entry is a different buying proposition: an unhandled 8.68 inch tool bar for turners who already own, or want to make, a handle. The bar is stainless steel with a replaceable carbide tipped blade held by screws, and the package includes the blade, two screws, a T20 wrench, and a 12 millimeter copper hoop. The maker notes it matches the black aluminum alloy handle sold in its own store, or a shop-made handle.

        Sold this way, it is the budget route into carbide parting, and it suits turners building a matched set of interchangeable bars around one favorite handle. The trade-offs are real: the tool cannot be used safely until mounted in a handle, and the short bar gives less reach than the full-size tools here, so it fits pen blanks, small boxes, and detail grooving better than large spindle stock. If you do not own a compatible handle, price the handled tools above before assuming this is cheaper.

        Specs

          • Maker: Asieg Tool
          • Bar length: 8.68 inches, stainless steel
          • Tip: replaceable tungsten carbide tipped blade
          • Joint diameter: 12 millimeters, copper hoop included
          • Included: 1 blade, 2 screws, 1 T20 wrench, 1 copper hoop
          • Handle: not included

          Easy Wood Tools Mid-Size Easy Parting Tool

          Easy Wood Tools built its name on replaceable carbide cutters, and its parting tool applies the idea differently from the bolt-on blades above. The negative rake carbide cutter is permanently mounted on a replaceable stainless steel blade: when the tip wears, you replace the blade, not the tool, using the included hex key. The maker credits the negative rake geometry for its smooth parting through natural and man-made materials, and it also allows side cutting and undercutting that a fixed square tip handles poorly.

          The cut itself is the narrowest here at 1/8 inch, which matters when parting a lidded box where lid and base grain should meet, or when slicing thin rings. The blade section is about 2.5 inches long, with a 14 inch maple handle and 19 inches overall, and the maker rates its reach for projects up to 5 inches in diameter. That ceiling is the honest limit: it is a small-to-mid-size lathe tool, not the choice for big bowl blanks.

          Specs

            • Maker: Easy Wood Tools, made in the USA
            • Model: PT150
            • Cut width: 1/8 inch
            • Cutter: negative rake carbide on a replaceable stainless steel blade
            • Blade length: about 2.5 inches
            • Handle: 14 inch maple; 19 inches overall

            How to Choose a Carbide Parting Tool

            Start with the tip system, because it decides your maintenance routine for years. Brazed tips, like the Simple Woodturning Tools and the long Asieg, cannot work loose and can be re-sharpened on diamond abrasives, but when the carbide is worn or chipped, the blade section must be replaced. Replaceable blades, like the Dirtech and the short Asieg bar, trade permanence for speed: unbolt, swap, and keep turning, at the cost of buying spares.

            Kerf width comes next. A 1/8 inch cut wastes the least wood and suits lidded boxes, thin rings, and any part-off where the two faces should meet with grain aligned. Wider cutters around 4 millimeters are stiffer and track straighter in deep plunges, but turn more of your blank into shavings. Match the kerf to the work you do most.

            Then check the bar and handle as a system. A square section sits flat on the rest and resists twisting; a round bar needs more attention to keep the cut vertical. Length should suit your lathe: 16 to 19 inch tools give leverage on full-size lathes, while mini lathe owners often find a shorter bar easier. If you buy an unhandled bar, confirm the joint diameter matches a handle you own, and that spare blades are stocked.

            Who Should Skip These Picks

            Traditional turners who already own a good high-speed steel parting tool and a grinder setup should skip this whole category: a ground HSS edge, refreshed in seconds, cuts as cleanly as carbide for most spindle work, and carbide adds cost without adding capability.

            Skip the unhandled Asieg bar if you do not own a compatible handle, since it cannot be used as sold. Skip the Easy Parting Tool if your work exceeds its stated project diameter range, and skip the longest Asieg if your lathe sits in a tight corner. Anyone expecting carbide to mean zero maintenance should skip all five: tips still dull, just more slowly, and sharpening carbide needs diamond abrasives.

            FAQ

            Can a carbide parting tool be sharpened?

            Yes, but not on a regular grinding wheel. Brazed tips are touched up with diamond abrasives, such as a diamond card or lapping plate, worked on the top face of the tip. Replaceable-blade designs are usually swapped for a fresh blade instead, although the Dirtech and Asieg makers state their tips can be sharpened as well as replaced.

            How wide a kerf should I choose for parting off a lidded box?

            Choose the narrowest tool you can control, which in this group is the 1/8 inch Easy Parting Tool. A thin kerf removes less wood, so the lid and base of a box keep more of their original length and the grain lines up across the joint. Wider cutters are better saved for large blanks where stiffness matters more.

            Do these tools work on resin and segmented blanks?

            Yes. Carbide holds its edge far longer than high-speed steel in abrasive material, and resin, glue lines, and mixed-media blanks are exactly where steel edges dull fastest. The Easy Wood Tools cutter is described by its maker as cutting through natural and man-made materials, and negative rake geometry is generally gentler on brittle resin.

            Does the unhandled Asieg bar fit any handle?

            It fits handles bored for its 12 millimeter joint, and the maker sells a matching aluminum alloy handle in its own store. A shop-made wooden handle bored to suit works as well, and the included copper hoop reinforces the joint. Check your handle’s socket diameter before ordering, because interchangeable systems are not standardized across brands.

            Final Verdict

            Carbide parting tools earn their place when sharpening downtime, abrasive stock, or resin work makes steel edges feel fragile. The Simple Woodturning Tools SPT is the buy-once pick: a brazed, re-sharpenable tip on a long interchangeable handle. The Dirtech is the practical middle, with a square bar and swappable blades. The two Asieg tools split by budget and setup, one long and handled, one a bare bar for handle owners. The Easy Wood Tools tool is the specialist for the finest 1/8 inch kerf. Choose by tip system and kerf first.

            Product and ASIN Reference

            Product ASIN
            Simple Woodturning Tools Carbide Parting Grooving Tool with 17 Inch Handle B01MFXHAE2
            Dirtech Parting Woodturning Tool, 16 Inch B08SMHX1R8
            Asieg Tool Carbide Parting and Grooving Tool, 19.68 Inch B07SJ6488D
            Asieg Tool 8.68 Inch Carbide Parting Tool with Copper Hoop B07ZJ3PD5R
            Easy Wood Tools Mid-Size Easy Parting Tool B00LY5P8PC
            J
            JD's Woodworks Editorial Team
            We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
            Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
            Best Carbide Parting Tools for Woodturning ComparedCheck price on Amazon

            Related guides

            Browse all Tools Workshop guides →

            More from Amazon

            Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

            Amazon Business

            A free business account with business pricing and bulk-buying tools for work, shop or home office.

            Create a business account
            Amazon Prime

            Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

            Start a Prime free trial
            Audible

            Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

            Try Audible free
            Amazon Music Unlimited

            Ad-free music streaming. Eligible new subscribers can start with a free trial.

            Try Music Unlimited free

            As an Amazon Associate we earn from qualifying purchases.