Key takeaways
- Compare the best dividers and compasses for woodworking layout: spring dividers, wing dividers and pencil compasses for arcs, circles and equal spacing.
What's inside
- 1. QWORK Precision Spring Dividers, 7-7/8 Inch Flat Leg (WD3790)
- 2. Big Horn 19053C 3-Piece 8-Inch Spring Caliper and Divider Set
- 3. ALLY Tools 12 Inch Precision Locking Wing Divider with Pencil Holder (WDPH12K)
- 4. Groz 12 Inch Spring Divider (01425)
- 5. Acrux7 3-Piece 8 Inch Spring Caliper Set
- How to Choose the Right Divider or Compass
- Conclusion
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
A good pair of dividers does jobs no tape measure can match. Set the points once and you can step off equal spacings along a board, transfer a measurement from one part to its mate without reading a scale, scribe arcs and circles, and check whether two diagonals or diameters really agree. Woodworkers use them for everything from laying out dovetails and turning blanks to dividing a panel into even sections for drawer pulls. This guide compares five dividers and compasses sold for shop layout work, from a single flat-leg spring divider to full three-piece caliper sets and a large pencil compass for wide arcs.
As an Amazon Associate, we earn from qualifying purchases.
This article contains affiliate links, and if you buy through them we may earn a commission at no extra cost to you.
1. QWORK Precision Spring Dividers, 7-7/8 Inch Flat Leg (WD3790)
The QWORK is a straightforward single-purpose layout divider: two flat steel legs joined by a bow spring at the top, with a knurled nut that opens and closes the points in fine increments. Because the adjustment is threaded, the setting holds while you walk the points along a board to step off equal divisions, and it will not drift the way a friction hinge can. The points are hardened and finely ground, so they scribe a clean line on wood and register positively in a punched center mark. At just under 8 inches long it covers the spacing work most furniture parts call for, and its light weight makes it easy to handle one-handed while the other hand holds a straightedge.
Specs:
– Type: Spring divider, flat legs
– Length: 7-7/8 in (about 8 in capacity)
– Material: Carbon steel with hardened, ground points
– Adjustment: Bow spring with knurled adjusting nut
– Weight: About 129 g
– Model: WD3790
2. Big Horn 19053C 3-Piece 8-Inch Spring Caliper and Divider Set
Big Horn bundles the three spring tools a turner or furniture maker reaches for most: an 8-inch divider for layout, an 8-inch outside caliper for checking diameters and thicknesses, and an 8-inch inside caliper for measuring mortise widths, grooves and bowl interiors. All three share the same bow-spring and threaded-spool adjustment, so a setting taken on a workpiece can be carried straight to a rule or a mating part. The legs are forged steel with hardened points and the springs are tempered for consistent tension. If you work at the lathe as well as the bench, this set covers diameter checks on blanks and spindles alongside ordinary divider work in one kit.
Specs:
– Type: 3-piece spring set (divider, outside caliper, inside caliper)
– Size: 8 in each
– Legs: Forged steel with hardened points
– Adjustment: Bow spring with threaded spool
– Includes: 8 in outside caliper, 8 in inside caliper, 8 in flat-leg divider
– Model: 19053C
3. ALLY Tools 12 Inch Precision Locking Wing Divider with Pencil Holder (WDPH12K)
The ALLY Tools wing divider swaps one steel point for a pencil holder, turning it into a true compass that draws the arc instead of just scribing it. The 12-inch legs swing wide enough for circles up to about 31 inches across, which suits tabletops, curved aprons and large templates that smaller dividers cannot reach. A knurled locking knob on the wing clamps the setting so the radius cannot creep mid-swing, and the holder accepts a standard carpenter’s pencil or a 2 mm lead holder. Two pencils and a sharpener are included, so it is ready to use out of the package. Choose this one when the job is drawing full-size curves rather than transferring point-to-point measurements.
Specs:
– Type: Wing divider / pencil compass
– Length: 12 in
– Circle range: About 1/2 in to 31 in diameter
– Material: High-carbon steel
– Adjustment: Wing with knurled locking knob
– Includes: Pencil holder, 2 pencils, pencil sharpener
– Model: WDPH12K
4. Groz 12 Inch Spring Divider (01425)
Groz builds this 12-inch divider for large layout work: stepping off long distances, striking big arcs and transferring dimensions from full-size patterns. The points are hardened to 50–55 HRC, a documented hardness figure most budget dividers do not publish, which helps them resist dulling and bending when scribing dense hardwoods or sheet goods. The spring joint uses a solid adjusting nut that runs smoothly and locks the legs exactly to dimension, and the fulcrum stud has a large bearing surface to prevent the legs deflecting sideways under pressure. A matte finish cuts glare under shop lights, making it easier to read where the points land.
Specs:
– Type: Spring divider
– Length: 12 in (300 mm capacity)
– Points: Hardened to 50–55 HRC
– Adjustment: Spring joint with solid adjusting nut
– Finish: Matte
– Weight: About 0.2 kg
– Model: 01425
5. Acrux7 3-Piece 8 Inch Spring Caliper Set
The Acrux7 set is aimed squarely at lathe work: an outside caliper for turning diameters, an inside caliper for hollowing and bore checks, and a divider for layout, all in 8-inch carbon steel. The divider handles the layout side of turning projects, marking center points, spacing beads and coves along a spindle, and transferring diameters between a blank and a finished reference piece. Each tool uses the same spring-and-nut adjustment, so settings are fine and repeatable. It is a practical starter set for anyone equipping a turning bench who does not yet own any spring tools.
Specs:
– Type: 3-piece spring set (divider, outside caliper, inside caliper)
– Size: 8 in each
– Material: Carbon steel
– Adjustment: Bow spring with adjusting nut
– Best for: Wood turning and lathe layout
– Model: ODUS-Spring Caliper
How to Choose the Right Divider or Compass
Spring divider vs. wing divider. A spring divider uses a bow spring and a threaded nut, which gives slow, precise adjustment and a setting that stays put; it is the better tool for stepping off equal divisions and transferring measurements. A wing divider opens wider and adjusts faster, and versions with a pencil holder double as a compass for drawing arcs. Many shops end up with one of each.
Size and capacity. An 8-inch divider covers most furniture layout: dovetail spacing, hardware placement and moderate arcs. Step up to a 12-inch model if you lay out tabletops, large casework or full-size templates, because a divider can only step a distance smaller than its leg span and draws a radius shorter than its full opening.
Points and adjustment quality. Look for hardened, finely ground points that come to a true needle tip; blunt or uneven points wander and tear the wood surface instead of scribing it. The adjusting nut should turn smoothly without backlash, and on wing dividers a locking knob is worth having so the setting cannot slip while you swing an arc.
Divider only, or a set with calipers? If you already own calipers, a single quality divider like the QWORK or Groz is all you need. If you turn wood or regularly check thicknesses and internal dimensions, a three-piece set that adds inside and outside calipers costs little more than a divider alone and covers far more measuring jobs.
Pencil holder or two steel points? Two steel points scribe the finest line and are what you want for measurement transfer. A pencil holder draws a more visible line and is better for rough layout and big curves, but the line is wider and less precise. Match the tool to whether you are measuring or drawing.
Conclusion
For most bench work, an 8-inch spring divider such as the QWORK is the single most useful layout tool in this group, with the Big Horn and Acrux7 three-piece sets adding calipers for turning and measurement checks. When the work gets bigger, the Groz 12-inch divider brings documented point hardness and a solid adjusting nut, while the ALLY Tools wing compass draws the wide arcs that point-to-point dividers cannot. Whichever you choose, a divider that holds its setting and has sharp, hardened points will make layout faster and more accurate than measuring with a rule alone.
Related guides
You might also like
- Best Laser Levels for Woodworking and Cabinet Layout
- Best Marking Gauges for Woodworking: 5 Top Picks 2026
- Best Hand Sanding Blocks for Woodworking: 5 Top Picks
- Best Miter Saw Stands for Woodworking: 5 Top Picks
- Best Zero Clearance Inserts for Table Saws: 5 Top Picks
- Best Countersink Drill Bit Sets for Wood: 5 Top Picks
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.