Updated Nov 18, 2026· 8 min read

Key takeaways

  • Compare the best zero clearance inserts for table saws, with model-specific fits for SawStop, SKIL, Ridgid and cabinet saws, plus materials and setup tips.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

The throat plate that ships with most table saws leaves a wide gap around the blade, and that gap causes real problems: thin offcuts drop in and jam against the blade, fibers on the underside of the workpiece tear out unsupported, and small cutoffs can be grabbed and thrown. A zero clearance insert closes that gap. The blade cuts its own slot through a blank plate, so the workpiece is supported right up to the teeth on both sides of the kerf. The result is cleaner cuts, less chip-out on plywood and melamine, and fewer small pieces disappearing into the saw.

As an Amazon Associate, we earn from qualifying purchases.

Because throat openings differ across brands and even across production years of the same saw, zero clearance inserts are sold as model-specific parts rather than universal accessories. The five picks below cover the most common fitments, from cabinet saws to jobsite models, in phenolic, UHMW, and laminated MDF. Measure your current insert before ordering any of them, since a plate that is even slightly off in length, width, or thickness will not sit flush.

This article contains affiliate links, and we earn a commission on qualifying purchases made through them at no extra cost to you.

1. SawStop TSI-SLD Standard Lock Down Insert

Check price on Amazon

SawStop’s own zero clearance insert is the natural choice for owners of the brand’s cast-iron saws. It is machined from a phenolic core with a melamine surface and is built specifically for the Industrial Cabinet Saw, Professional Cabinet Saw, and Contractor Saw running standard 10-inch blades. Unlike generic plates, it has preformed clearance slots for the SawStop blade guard and riving knife, plus dual metal wear plates where the anti-kickback pawls ride.

The standout feature is the positive locking latch, which lets you swap inserts tool-free after adjusting the side screws for a snug fit. Buyers commonly keep one insert dedicated to 90-degree cuts and a second for bevel work, because once a plate is cut at an angle it no longer provides zero clearance for straight cuts. If you run a SawStop cabinet or contractor saw and want a factory-engineered fit with the safety hardware fully accommodated, this is the insert to get.

Specs:
– Fits: SawStop Industrial Cabinet Saw, Professional Cabinet Saw, and Contractor Saw (10-inch standard blades; Jobsite Saw not included)
– Material: Phenolic core with melamine surface
– Locking: Positive locking latch for tool-free changes
– Features: Preformed slots for blade guard and riving knife; dual metal wear plates for anti-kickback pawls
– Adjustment: Side screws for a snug, flush fit
– ASIN: B0040H2WZU
– Link: https://www.amazon.com/dp/B0040H2WZU?tag=powertoolsdiy04-20

2. SKIL STZ6307 Zero Clearance Table Saw Insert Plate

Check price on Amazon

SKIL sells this insert as the matched accessory for its popular 15-amp 10-inch jobsite saw, the TS6307-00. It is a dedicated plate for that one model, which removes the guesswork that comes with universal inserts: the outline, thickness, and retention match the saw’s throat opening exactly. The blank plate is cut in the usual way, by lowering the blade and raising it slowly through the insert to form a slot matched to your blade.

The STZ6307 is designed for precise cuts at 90 degrees and reduces the kerf clearance to the thickness of the blade itself, which noticeably cuts down tear-out on sheet goods compared with the saw’s stock plate. A quick-release design makes it easy to swap back to the dado plate when needed. Owners of the TS6307-00 who want an OEM fit rather than a trim-to-fit aftermarket plate should start here, and should follow SKIL’s guidance about the riving knife position during the first break-in cut.

Specs:
– Fits: SKIL TS6307-00 15-amp 10-inch jobsite table saw only
– Model number: STZ6307
– Cut angle: 90 degrees
– Design: Quick-release insert plate; blade cuts its own zero-clearance slot
– UPC: 195532200117
– ASIN: B0BFVGMDPS
– Link: https://www.amazon.com/dp/B0BFVGMDPS?tag=powertoolsdiy04-20

3. ZEROSERT R-10-2-L Zero Clearance Inserts, 2-Pack

Check price on Amazon

ZEROSERT takes a different approach for the Ridgid R4510 and R45101 jobsite saws: instead of a single phenolic plate, you get a two-pack of laminated inserts, one for standard blades and one sized for a dado stack. The inserts are made from eco-friendly MDF surfaced with Wilsonart laminate, which gives a slick, low-friction top that stock slides across easily, and the maker is Robert Lee Handcrafts, the company behind the Leecraft insert line.

Each insert measures about 13-15/16 inches long by 3-11/16 inches wide, and the pair together weighs just over a pound, so keeping a spare in the shop costs nothing in space. Pre-drilled holes let you secure the plate using the fasteners from the saw’s original insert. For R4510 owners, the bundle is the practical angle: one purchase covers both your everyday blade and your dado setup, and the lower-cost laminated construction makes it painless to replace an insert once its slot wears or a blade change widens it.

Specs:
– Fits: Ridgid R4510 and R45101 table saws
– Contents: 2 laminated inserts (1 standard, 1 dado)
– Material: Eco-friendly MDF with Wilsonart laminate surface
– Individual insert size: 13-15/16 in L x 3-11/16 in W (about 14 x 3-3/4 x 1/2 in overall)
– Blade compatibility: Thin kerf, full kerf, and dado sets
– ASIN: B09TZD51G1
– Link: https://www.amazon.com/dp/B09TZD51G1?tag=powertoolsdiy04-20

4. Fulton UHMW Zero Clearance Insert for Jet, Grizzly, and Powermatic 64 (PW956)

Check price on Amazon

Sold by Peachtree Woodworking Supply under its Fulton Woodworking Tools line, the PW956 fits the smaller cabinet and contractor saws that use a 12-1/2 by 3-1/2 inch throat opening, including the Powermatic 64 and 64A, small Grizzly models, and Jet saws in that size class. It is machined from UHMW, an ultra-high-molecular-weight plastic chosen for its abrasion resistance and naturally slick surface, and it can be used with standard carbide-tipped blades as well as dado blades.

UHMW behaves differently from phenolic: it is tough and forgiving rather than hard and rigid, so it stands up well to daily shop use and is easy on blade teeth if contact ever occurs. As with every insert in this roundup, the fitment list is a starting point rather than a guarantee, since these saws changed details over long production runs. Measure your factory insert’s length, width, and thickness against the PW956 dimensions before ordering.

Specs:
– Fits: Jet, small Grizzly, and Powermatic 64/64A table saws
– Dimensions: 12-1/2 in x 3-1/2 in x 7/16 in
– Material: UHMW
– Model: PW956 (Fulton Woodworking Tools, sold by Peachtree Woodworking Supply)
– Blade compatibility: Standard carbide-tipped blades and dado blades
– ASIN: B000H6HGYK
– Link: https://www.amazon.com/dp/B000H6HGYK?tag=powertoolsdiy04-20

5. Leecraft Zero Clearance Insert for Hitachi C10FL and Porter Cable PCB270TS

Leecraft is the best-known name in aftermarket throat plates, and this phenolic insert covers a pair of widely owned older saws: the Hitachi C10FL and C10LA, and the Porter Cable PCB270TS. It is made from Leecraft’s high-density phenolic laminate with a bonded melamine surface, the same construction the company uses across its range, and it is designed for use with carbide-tipped blades only.

The insert supports the workpiece right up to the blade, reducing splintering and chip-out on the bottom side of regular cuts, and the blade raises through the blank to cut a slot matched to its own kerf. At roughly 15-1/8 inches long, it is sized for the larger throat openings of these saws, which is exactly why owners of these models struggle with generic inserts. If you run a C10FL or PCB270TS and want the established aftermarket option rather than a shop-made plate, this is the one.

Specs:
– Fits: Hitachi C10FL and C10LA; Porter Cable PCB270TS
– Material: High-density phenolic laminate with bonded melamine surface
– Length: About 15-1/8 in (measure your factory insert before ordering)
– Blade requirement: Carbide-tipped blades only
– ASIN: B003ELQYKW
– Link: https://www.amazon.com/dp/B003ELQYKW?tag=powertoolsdiy04-20

How to Choose the Right Zero Clearance Insert

Match the exact saw model first. Zero clearance inserts are not universal. Throat openings vary in length, width, thickness, and end shape, and manufacturers changed them over the years. The reliable method is to remove your factory insert and measure it, then compare those three dimensions with the listing before you order.

Pick a material for how you work. Phenolic laminate is the traditional choice: rigid, flat, durable, and slick, and it is what most premium inserts use. UHMW is tougher and more forgiving, with a naturally low-friction surface. Laminated MDF costs less and is sold in multi-packs, which suits woodworkers who dedicate separate inserts to different blades and replace them as wear items.

Plan one insert per setup. An insert is only zero clearance for the blade and angle that cut it. Most woodworkers keep separate inserts for a standard blade at 90 degrees, for bevel cuts, and for each dado width they use regularly. Multi-packs and lower-cost laminated inserts make that system affordable.

Check the safety hardware. If your saw has a riving knife, splitter, or anti-kickback pawls, confirm the insert has the slots or clearance those parts need, or be prepared to cut that clearance yourself. An insert that forces you to remove the riving knife for everyday cuts is the wrong insert.

Cut the slot safely. Clamp a board across the insert so it cannot lift, stand to the side, and raise the spinning blade slowly through the plate. Never hold a blank insert down by hand while cutting the slot, and let the blade reach full speed before you start raising it.

Conclusion

A zero clearance insert is one of the cheapest upgrades that changes how a table saw actually cuts: less tear-out, better support for thin stock, and fewer offcuts vanishing into the throat. SawStop owners should start with the factory TSI-SLD for its locking latch and preformed safety slots. SKIL TS6307-00 owners get an exact OEM fit from the STZ6307, while Ridgid R4510 owners get the best value from the ZEROSERT two-pack that covers dado work as well. For older cabinet and contractor saws, the Fulton PW956 in UHMW and the Leecraft phenolic insert for Hitachi and Porter Cable saws cover two of the most common legacy fitments. Whichever you choose, measure your current insert first, and dedicate one plate to each blade setup you use.

J
JD's Woodworks Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Zero Clearance Inserts for Table Saws: 5…Check price on Amazon

Related guides

Browse all Uncategorized guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.