Updated Nov 20, 2026· 8 min read

Key takeaways

  • Compare five Western dovetail saws with brass backs, rip-filed teeth and resharpenable plates, from Sheffield gent's saws to a budget Bahco pick.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

The best Western dovetail saw is a push-stroke backsaw with a brass or steel spine, a plate around 0.020 inch thick, and teeth in the 14 to 20 TPI range. If you want one answer: pick the Thomas Flinn Gent 10 inch for full-size furniture dovetails, the Lynx 8 inch for smaller boxes and drawers, and the Bahco ProfCut for a budget hardpoint saw that never needs filing.

Every saw below follows the traditional Western pattern rather than the Japanese pull-saw pattern covered in the site’s other dovetail guides. A folded or rolled back stiffens the plate so it tracks straight on the push stroke, the teeth are soft enough to be resharpened with a saw file instead of replaced, and a pistol-grip or turned gent’s handle puts your index finger in line with the cut. Published plate, tooth and handle specifications are what separate the five picks, because two saws that look alike can leave very different kerfs in a tail board.

As an Amazon Associate, we earn from qualifying purchases.

Table of Contents

Quick Answer

The best Western dovetail saw for most benches is a rip-filed, brass-backed push saw around 14 to 20 TPI. The Thomas Flinn Gent 10 inch leads this list for full-size furniture dovetails, the Lynx 8 inch suits smaller work, and the Bahco ProfCut covers the budget tier with hardpoint teeth that never need filing.

Thomas Flinn Gent Dovetail Saw 10 Inch

Check price on Amazon

The Thomas Flinn Gent is the full-size option in this group, built in Sheffield, England, with a 10 inch high-carbon steel plate and a solid rolled brass back. The extra blade length over the 8 inch saws below gives a longer stroke on each pass, which suits casework dovetails in thicker drawer sides and carcass parts where a shorter plate runs out of travel.

The teeth are cut at 20 TPI and are resharpenable, so the saw is maintained with a slim taper file rather than replaced. Published figures put the kerf at about 0.028 inch, wider than a Japanese dozuki but typical for a Western plate of this class, and the walnut handle with a brass ferrule follows the traditional gent’s pattern. It sits at a premium tier, and the weight of the rolled brass back does much of the work on the push stroke, so the correct technique is a light grip and a steady pass.

Specs:

  • Blade length: 10 inches
  • Teeth: 20 TPI, resharpenable
  • Plate: high-carbon steel
  • Back: solid rolled brass
  • Handle: walnut with brass ferrule
  • Kerf: about 0.028 inch, as listed
  • Origin: Sheffield, England
  • Tier: premium

Lynx Thomas Flinn Taytools British 8 Inch Dovetail Saw

Check price on Amazon

The Lynx 8 inch is the saw to reach for when the work shrinks to small boxes, drawer parts and thin stock. Its 8 inch plate is Sheffield alloy spring steel at about 0.022 inch thick, and this version is filed for rip cutting, the filing a dovetail actually needs because tails and pins are sawn along the grain. Many fine-toothed saws this size are filed crosscut, so the rip filing earns this Lynx its place here.

A folded brass back stiffens the plate, the handle is stained European beech fixed with brass screws, and the teeth are hand-sharpened at the factory and can be resharpened at home. Published depth under the back is about 2-1/4 inches, enough for drawer sides and box parts, and the saw is listed at about 16 ounces, substantial without being tiring on a long run of pins. It is a mid-range tier saw that covers most small-scale dovetailing on its own.

Specs:

  • Blade length: 8 inches
  • Teeth: 20 TPI, filed for rip cutting, resharpenable
  • Plate: alloy spring steel, about 0.022 inch
  • Back: folded brass
  • Handle: stained European beech with brass screws
  • Depth of cut: about 2-1/4 inches
  • Weight: about 16 ounces, as listed
  • Origin: Sheffield, England
  • Tier: mid-range

Two Cherries 520-6020 Brass Back Dovetail Saw

Check price on Amazon

Two Cherries brings the German entry to this list. The 520-6020 pairs a 10 inch blade of German high-carbon steel with a solid brass back and a closed wooden handle, and it arrives pre-sharpened. At 15 TPI the teeth are noticeably coarser than the 20 TPI Sheffield saws above, which changes the character of the cut: it starts more willingly and clears waste faster in thicker stock, at the cost of a slightly rougher kerf wall.

That makes this the pick for woodworkers who cut dovetails in three-quarter inch furniture stock more often than in thin drawer parts, and who find very fine teeth slow going. The teeth are conventional soft steel rather than hardpoint, so they can be resharpened with a file when they dull. It sits in the mid-range tier and is sold in the United States through Robert Larson, the importer of the Two Cherries line.

Specs:

  • Blade length: 10 inches
  • Teeth: 15 TPI, pre-sharpened, resharpenable
  • Plate: German high-carbon steel
  • Back: solid brass
  • Handle: closed wooden handle
  • Model: 520-6020
  • Origin: Germany
  • Tier: mid-range

Thomas Flinn Pax 8 Inch Gent’s Dovetail Saw

Check price on Amazon

The Pax name dates back to 1776 and is now made by Thomas Flinn in Sheffield, and this 8 inch gent’s saw is the compact traditional option. The plate is high-carbon steel with 20 TPI teeth under a solid rolled brass back, and the turned walnut handle follows the gent’s pattern, with the grip in line with the plate rather than angled like a pistol grip, so the push comes straight from the wrist.

Like the other Sheffield saws here, the teeth are resharpenable, and the published kerf is in the same range as the larger Flinn Gent. Choose this one over the Lynx if you prefer a turned handle and the Pax pattern, and over the 10 inch Gent if nearly all of your dovetails are in drawer sides, small boxes and other thin stock. It is a mid-range tier saw, a step above the Lynx in finish.

Specs:

  • Blade length: 8 inches
  • Teeth: 20 TPI, resharpenable
  • Plate: high-carbon steel
  • Back: solid rolled brass
  • Handle: turned walnut, gent’s pattern
  • Origin: Sheffield, England
  • Tier: mid-range

Bahco PC-10-DTR ProfCut Dovetail Saw

Check price on Amazon

The Bahco ProfCut is the budget tier pick and the only hardpoint saw in this roundup. Its 250 mm blade carries universal toothing at 13/14 TPI with induction-hardened teeth and a light steel back. Hardpoint teeth hold an edge far longer than soft filed teeth, but once they finally dull they cannot be resharpened, so the saw is a long-life consumable rather than a lifetime tool.

The straight handle is a deliberate design point: it lets the saw cut flush against a surface, which makes the ProfCut handy for trimming plugs and dowels as well as for the joints themselves. Bahco lists the plate at 0.5 mm and the saw at 190 grams, the lightest tool here by a wide margin. For a first Western dovetail saw, or a practice saw for learning on spare stock, it covers the job at a budget tier.

Specs:

  • Blade length: 10 inches (250 mm)
  • Teeth: 13/14 TPI universal toothing, hardpoint, not resharpenable
  • Plate: steel, 0.5 mm
  • Back: light steel back
  • Handle: straight wooden handle, allows flush cutting
  • Weight: 190 grams, as listed
  • Model: PC-10-DTR
  • Tier: budget

How to Choose

Start with the filing. Dovetails are rip cuts, so a rip-filed saw tracks the grain cleanly; a crosscut-filed saw still works but tends to leave a fuzzier kerf wall. Next, match tooth count to stock thickness: 20 TPI suits thin drawer sides and small boxes, 15 TPI is the middle ground for general furniture work, and the coarser Bahco pattern is aimed at faster, less delicate cutting. Keep at least three or four teeth in the thickness of the stock as a working rule.

Then weigh plate and back. A brass back adds mass that steadies the push stroke and is the traditional choice on the Sheffield and German saws; the Bahco’s steel back keeps weight and cost down. Plate thickness around 0.020 to 0.022 inch is the Western norm and sets the kerf width. Finally, decide on maintenance: soft teeth on the Flinn, Lynx, Pax and Two Cherries saws can be resharpened for decades with an inexpensive file, while the Bahco’s hardpoint teeth trade that service life for zero upkeep until they wear out.

Who Should Skip

Skip Western dovetail saws entirely if you already cut clean dovetails with a Japanese dozuki and prefer the pull stroke; the push stroke, heavier backs and wider kerfs here solve problems you may not have. Skip the resharpenable Sheffield saws if you have no interest in learning to file teeth, since a dull soft-tooth saw cuts worse than a hardpoint saw and the Bahco exists for that case. And skip the 8 inch saws if your dovetails are mostly in thick carcass stock, where the 10 inch plates give a longer, steadier stroke.

FAQ

What does rip-filed mean, and why does it matter for dovetails?

Rip teeth are filed straight across the plate so each tooth works like a small chisel moving along the grain. Dovetail tails and pins are cut with the grain, so a rip-filed saw cuts faster and leaves a cleaner wall than a crosscut-filed saw of the same tooth count, whose beveled teeth are shaped for slicing across fibers.

Can a Western dovetail saw be resharpened?

Yes, as long as the teeth are conventional soft steel, as on the Thomas Flinn, Lynx, Pax and Two Cherries saws here. A slim taper saw file and a saw vise restore the edge, and the set can be adjusted with a saw set. Hardpoint teeth like the Bahco’s are induction hardened and cannot be filed.

Which blade length is better, 8 inch or 10 inch?

An 8 inch plate is easier to control on small work such as drawers and boxes. A 10 inch plate gives a longer stroke, which cuts faster and straighter in thicker furniture stock. Match the saw to the thickest stock you dovetail regularly rather than buying for the occasional oversized piece.

How deep can a dovetail saw cut?

Depth is limited by the back, not the blade length. The saws here allow roughly 2 to 2-1/2 inches of depth under the back, which covers drawer sides, box parts and most furniture dovetails. Deeper work calls for a tenon saw or a different joint layout, not a longer dovetail saw.

Final Verdict

For a traditional Western dovetail saw, the Thomas Flinn Gent 10 inch is the most complete pick: Sheffield build, a rolled brass back, resharpenable 20 TPI teeth and enough plate for furniture-scale work. The Lynx 8 inch is the better buy for small work because of its rip filing, the Two Cherries suits faster cutting in thick stock, the Pax covers compact traditional work, and the Bahco ProfCut is the honest budget option. Choose by stock thickness, handle pattern and how you feel about sharpening.

J
JD's Woodworks Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Western Dovetail Saws: 5 Traditional Backsaw PicksCheck price on Amazon

Related guides

Browse all Uncategorized guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.